Deals of The Day
Ends in:
Carbon Fiber Tubes and Rods, Mechanical and Workbench
Pultruded Carbon Fiber Tube (Hollow) 10mm(OD) * 8mm(ID) * 1000mm(L) (Pack of 2)
-8%
Carbon Fiber Tubes and Rods, Mechanical and Workbench
Pultruded Carbon Fiber Tube (Hollow) 10mm(OD) * 8mm(ID) * 1000mm(L) (Pack of 2)
Made of Carbon Fiber material
Very Strong and Light
Smooth finish
High Tensile Strength
Excellent quality
Resistance to ultraviolet light.
Anti-aging and corrosion resistance.
SKU: n/a
Nuts-Bolts and Spacers
EasyMech Set of M4 X 8MM Socket Head Cap (Allen) Bolt and Nut-12 pcs.
Brand: EasyMech
Type: M4 (4.0 mm Bolt Diameter)
Bolt Head Outer Diameter: 6.8 mm
Bolt Length: 8 mm
Bolt Head Style: Round
Bolt Drive Style: Hex Socket
Color: Black
Nut Type: Hex
Nut Outer Diameter: 7 mm
Allen Key size Required: 3 mm.
Hardness is 2 times higher than copper,10 times higher than aluminum.
SKU: n/a
Drone Parts, Flight Controller & Accessories
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
-8%
Drone Parts, Flight Controller & Accessories
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
Supported Receiver Input Signal: PPM, SBUS, DSM
Support PPM, SBUS, DSM receiver input signal
Battery voltage detection and buzzer interface
Run on SP RACING F3 EVO firmware 32 brush flight control
Large current NMOS transistors, operating current can reach 10A or higher
Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: n/a
Drone Parts, FPV Antennas and Trans-Receivers
TS832 48Ch 5.8G 600mW Wireless Audio/Video Transmitter for FPV RC
-22%
Drone Parts, FPV Antennas and Trans-Receivers
TS832 48Ch 5.8G 600mW Wireless Audio/Video Transmitter for FPV RC
Transmitter 600mW/48CH >up to 1km(open area).
Frequency control: built-in frequency and phase lock loop.
Transmitter module connector: Female RP-SMA.
Antenna connector: Male RP-SMA.
Supply Voltage: 7-24 V
Current: 220 mA.
48 CH is compatible with all FPV 5.8g receivers.
SKU: n/a
Featured Products
-
Display Modules, HMI LCD Display
10.1inch Resistive Touch Screen IPS LCD
- 10.1inch IPS screen,1024 × 600 high resolution.
- Resistive touch control.
- Compatible and Direct-connect with any revision of Raspberry Pi (If you are using a Raspberry Pi Zero / Zero 2 W, an additional HDMI cable is required).
- Supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems.
- Also works as a computer monitor, in this case, the touch panel is unavailable and an HDMI cable is required.
- HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os).
- OSD menu, supports brightness/contrast ratio adjustable manually.
SKU: n/a -
Display Modules, HMI LCD Display
AD409 Pro-ES HDMI Digital Microscope with Endoscope
- High-quality metal lens and focusing barrel
- Microscope with Endoscope all-around view 360°
- Professional HDMI digital microscope supports multiple output methods
- Soldering Microscope with Pro Metal Stand
- Unique UV filter design
- 8 Levels Adjustable LED Lights
- Convenient Wireless Remote Control
- Professional Measurement Software
- Easy to use, more than a microscope
SKU: n/a -
Development Boards, Robot Chasis
Aluminium Tank Robot Chassis with Dual 12V Motors
- Wheels and Tracks are made of plastic
- Structure is sturdy and stable, with body made of metal
- 33mm Motors can operate at 9V to 12V (300 RPM)
- Tons of mounting holes & slots!
- Size: 185mm X 200mm X 60mm (L X W X H)
SKU: n/a -
-
Development Boards, Robot Chasis
MasterPi AI Vision Chassis with Mecanum Wheels and Robot Arm
- Stable power supply assured with an autonomous power switch.
- Over-current safeguard for the 6-channel PWM servo ports.
- Embedded MCU to lighten the load on the Raspberry Pi and optimize resource consumption.
- Equipped with various features like RGB light, buzzer, and LED light.
- Expandability facilitated through three IIC ports.
- Numerous GPIO pins available for development purposes.
- Compatibility with Hiwonder sensors ensured with 4PIN anti-reverse ports.
SKU: n/a -
Development Boards, Robot Chasis
ArmPi Pro ROS Robot Chassis with Robot Arm
- Independent power switch for stable power supply
- 6-channel PWM servo ports with over-current protection
- Loaded MCU to offload the workload of Raspberry Pi and reduce resource usage
- Loaded with RGB light, buzzer, LED light, etc.
- Three IIC ports for expansion
- Lead out multiple GPIO pins for development
- 4PIN anti-reverse ports compatible with Hiwonder sensors
SKU: n/a -
-
Best Selling Products
-
-
Carbon Fiber Tubes and Rods, Mechanical and Workbench
Pultruded Carbon Fiber Tube (Hollow) 10mm(OD) * 8mm(ID) * 1000mm(L) (Pack of 2)
-8%Carbon Fiber Tubes and Rods, Mechanical and WorkbenchPultruded Carbon Fiber Tube (Hollow) 10mm(OD) * 8mm(ID) * 1000mm(L) (Pack of 2)
- Made of Carbon Fiber material
- Very Strong and Light
- Smooth finish
- High Tensile Strength
- Excellent quality
- Resistance to ultraviolet light.
- Anti-aging and corrosion resistance.
SKU: n/a -
Nuts-Bolts and Spacers
EasyMech Set of M4 X 8MM Socket Head Cap (Allen) Bolt and Nut-12 pcs.
- Brand: EasyMech
- Type: M4 (4.0 mm Bolt Diameter)
- Bolt Head Outer Diameter: 6.8 mm
- Bolt Length: 8 mm
- Bolt Head Style: Round
- Bolt Drive Style: Hex Socket
- Color: Black
- Nut Type: Hex
- Nut Outer Diameter: 7 mm
- Allen Key size Required: 3 mm.
- Hardness is 2 times higher than copper,10 times higher than aluminum.
SKU: n/a -
Drone Parts, Flight Controller & Accessories
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
-8%Drone Parts, Flight Controller & AccessoriesF3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Run on SP RACING F3 EVO firmware 32 brush flight control
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: n/a -
-
Drone Parts, FPV Antennas and Trans-Receivers
TS832 48Ch 5.8G 600mW Wireless Audio/Video Transmitter for FPV RC
-22%Drone Parts, FPV Antennas and Trans-ReceiversTS832 48Ch 5.8G 600mW Wireless Audio/Video Transmitter for FPV RC
- Transmitter 600mW/48CH >up to 1km(open area).
-
Frequency control: built-in frequency and phase lock loop.
- Transmitter module connector: Female RP-SMA.
-
Antenna connector: Male RP-SMA.
-
Supply Voltage: 7-24 V
-
Current: 220 mA.
-
48 CH is compatible with all FPV 5.8g receivers.
SKU: n/a
Recommended For You
-
Carbon Fiber Tubes and Rods, Mechanical and Workbench
3K Roll-wrapped Carbon Fibre Tube (Hollow) 10mm(OD) * 8mm(ID) * 500mm(L)
-11%
Carbon Fiber Tubes and Rods, Mechanical and Workbench3K Roll-wrapped Carbon Fibre Tube (Hollow) 10mm(OD) * 8mm(ID) * 500mm(L)
- Made of Carbon Fiber material
- High Strength
- Stable dimension and UV resistant
- High Corrosion Resistance
- High Thermal Conductivity in some forms
- Low coefficient of thermal expansion
- Non-poisonous
SKU: n/a -
