Flight Controller & Accessories
Showing 25–48 of 56 results
-
Drone Parts, Flight Controller & Accessories
F3 EVO V2.0 Flight Control
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: n/a -
-
Drone Parts, Flight Controller & Accessories
OpenPilot CC3D EVO Flight Controller Straight Pin
- 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
- Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance.
- Software support for Windows, Mac, and Linux.
- Direct high-speed USB support with no drivers required, a true plug and play device.
- Spektrum satellite receiver support.
- Futaba S-BUS hardware support.
- Innovative Flexi-port technology for superior port flexibility.
- 4Mbits onboard EEPROM for configuration storage.
SKU: n/a -
Drone Parts, Flight Controller & Accessories
Naze32 6DOF Flight Control board
- Battery voltage monitoring.
- Built-in FrSky telemetry converter.
- Modern 32-bit processor (STM32 F103) running at 3.3V/72MHz.
- Onboard USB for setup and configuration.
- Modern GUI for all operating systems, Baseflight Configurator.
SKU: n/a -
Drone Parts, Flight Controller & Accessories
Mini USB (90° Connector) to FPV AV Output Cable for GoPro Hero 3
-5%
Drone Parts, Flight Controller & AccessoriesMini USB (90° Connector) to FPV AV Output Cable for GoPro Hero 3
- USB connector is used to connect to the USB port on your GoPro Hero3 Camera.
- The 3 pin female connector is for AV video output
- Typical application:
Video output from your GoPro Hero 3 USB port to your video wireless transmitter. (Connect your GoPro Hero 3 directly to FPV transmitter)
SKU: n/a -
-
Drone Parts, Flight Controller & Accessories
Mini OSD for Pixhawk Flight Controller
- ATmega328P with Arduino bootloader
- MAX7456 monochrome on-screen display
- FTDI cable compatible pinout
- Standard 6 pin ISP header
- 2 independent power sections with an LED indicator on each
- Solder jumpers for combining the power sections
SKU: n/a -
-
Drone Parts, Flight Controller & Accessories
SP RACING F3 FC Replacement Accessories Set
Accessories compatible with SP RACING F3 Flight Controller Module
High-quality cable and connectors.
1 x 3*8 Burg connector(Straight)
1 x 3*8 Burg connector(Right-angle)
1 x 1*10 Burg Connector(Straight)
2 x 2pt cable
2 x 4pt cable
2 x 8pt cableSKU: n/a -
Drone Parts, Flight Controller & Accessories
F3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
-8%
Drone Parts, Flight Controller & AccessoriesF3 Brushed Flight Control Board Based On SP RACING F3 EVO Brush for Micro FPV Frame
- Supported Receiver Input Signal: PPM, SBUS, DSM
- Support PPM, SBUS, DSM receiver input signal
- Battery voltage detection and buzzer interface
- Run on SP RACING F3 EVO firmware 32 brush flight control
- Large current NMOS transistors, operating current can reach 10A or higher
- Use STM32F303CCT6 + MPU6500, advanced hardware platform F3 for higher flight stability
SKU: n/a -
Drone Parts, Flight Controller & Accessories
DJI NAZA M V2 Multirotor Autopilot Controller set with GPS
-10%
Drone Parts, Flight Controller & AccessoriesDJI NAZA M V2 Multirotor Autopilot Controller set with GPS
- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Supported ESC Output 400 Hz refresh frequency
- Supported Transmitters PCM or 2.4 GHz radio with at least 4 channels
- Power Consumption MAX: 1.5 W (0.3 A at 5 V)
- Operating Temperature: -10 to 50°C
SKU: n/a -
Drone Parts, Flight Controller & Accessories
DJI NAZA-M Lite V1.1 with GPS Kit
- Supported Multi-Rotor: Quad-rotor I4, X4 / Hex-rotor I6, X6, IY6, Y6.
- Supported ESC Output: 400Hz refresh frequency.
- Recommended Transmitter: PCM or 2.4GHz with minimum 4 channels.
- Power Consumption: MAX1. 5W (0.3A@5V) Normal:0.6W (0.12A@5V).
- Weight: MC:25g; VU:20g; GPS:21.3g.
- All-in-One Design.
- Advanced attitude stabilized Algorithm.
- Multiple flight control mode/intelligent switching.
- GPS Module Available/Accurate Position hold.
- Intelligent Orientation Control (IOC).
- Failsafe mode.
SKU: n/a -
Drone Parts, Flight Controller & Accessories
OMNIBUS F4 V2 PRO Flight Controller with SD Card Slot & BEC
-20%
Drone Parts, Flight Controller & AccessoriesOMNIBUS F4 V2 PRO Flight Controller with SD Card Slot & BEC
- Dimensions: 37 x 37 x 10 mm(L x H x W)
- Weight: 12 gm.
- SPI Gyro MPU6000
- MicroSD Blackbox
- F4 Processor (F405)
- 5v3a SBEC
- Built-in Current Sensor
- On-Board OSD (controlled by Beta flight, FC over SPI bus)
- On-Board Video Filter (only can supply 5V to VTX and Camera)
- On-Board Voltage Regulator and Power supply (BEC)
SKU: n/a -
Drone Parts, Flight Controller & Accessories
SP Racing F3 Flight Controller ACRO Version
- The STM32F3 CPU, MPU 6050 sensor, 16M high-capacity flash memory, OSD function.
- The SP F3 runs Cleanflight which can be configured to suit your needs using a cross-platform GUI (Windows/OSX/Linux).
- Tiny and lightweight, the Racing F3 has a standard 36x36mm form-factor with 30.5mm mounting holes and weighs just 6 grams.
- Flight Logging, on-board high-capacity black box flight log recorder – optimize your tuning and see the results of your setup without guesswork.
- OneShot ESC, full support for OneShot ESCs for easy PID tuning and a sharper response.
- Broad RC receiver supports SBus, SumH, SumD, Spektrum1024/2048, XBus, PPM, PWM receivers, no external inverters required (built-in).
SKU: n/a -
Drone Parts, Flight Controller & Accessories
Pixhawk I2C Port Expand Board with Cable
- Package Weight: 5 gm
- Number of Ports: 5.
- Board Dimensions: 33 x 12 x 6 mm(LxWxH)
- Net Weight: 3g
- Brand new and high quality
- The I2C splitter expands the I2C port to allow up to four additional peripherals to connect to Pixhawk.
SKU: n/a -
-
-
Drone Parts, Flight Controller & Accessories
DJI Naza M Lite Multi-Rotor Flight Controller without GPS
-15%
Drone Parts, Flight Controller & AccessoriesDJI Naza M Lite Multi-Rotor Flight Controller without GPS
- Input Voltage (V): MC: 4.8V~5.5V (recommended 2S~6S Lipoly).
- Power Consumption: MAX: 1.5W (0.3A @ 5V), Normal: 0.6W (0.12A @ 5V).
- Operating Temperature:-10°C ~ +50°C.
- Supported ESC Output: 400Hz refresh frequency
SKU: n/a
