Brushed / Brushless DC motor Driver
Showing 1–24 of 26 results
-
-
Brushed / Brushless DC motor Driver, Motors
Motor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N
-24%
Brushed / Brushless DC motor Driver, MotorsMotor Driver TB6612FNG Module Performance Ultra Small Volume 3 PI Matching Performance Ultra L298N
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Operating Voltage(VDC): 15
- Peak Current (A): 3.2
- Continuous Current (A): 1.2
- No. of Channels: 1
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
-19%
Brushed / Brushless DC motor Driver, Motors20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch with Case
-10%
Brushed / Brushless DC motor Driver, Motors12V 24V 36V 40A PWM DC Motor Speed Controller Forward Reverse Adjustable Knob Switch with Case
- Input voltage: DC12 to 36V (equal to the rated voltage of the motor)
- Output voltage: linear under load
- Maximum current: 50A
- Continuous current: 40A
- Support motor: DC brush motor
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
-8%
Brushed / Brushless DC motor Driver, MotorsCytron 10 A Switch Control Potentiometer DC Motor Driver (MD10POT)
1. The MD10-POT control circuit is specifically crafted to facilitate speed control through the use of an included 10K Ohm potentiometer.
2. It is important to note that this control circuit does not function with analog voltage from an external controller.
3. For convenient operation, a 3-way rocker switch is incorporated, serving the dual purpose of initiating or stopping the motor and controlling its direction.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
-14%
Brushed / Brushless DC motor Driver, MotorsCytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
MD13S 13Amp DC Motor Driver – GROVE Compatible
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
-12%
Brushed / Brushless DC motor Driver, MotorsCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
-17%
Brushed / Brushless DC motor Driver, MotorsMonster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 34 mΩ
- Maximum PWM frequency: 10 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
SmartElex 10D Smart Motor Driver (Powered by Raspberry Pi)
-11%
Brushed / Brushless DC motor Driver, MotorsSmartElex 10D Smart Motor Driver (Powered by Raspberry Pi)
- Onboard 5V 3A Buck Converter.
- Continuous 10A maximum current without Heatsink.
- Two brushed DC motor Bidirectional control.
- Current limiting at 35A.
- PWM and direction-controlled driving of four externally powered NMOS transistors
- Type-C USB for SERIAL Mode
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Dual channel 10A Motor Driver UNO Robot Controller
-13%
Brushed / Brushless DC motor Driver, MotorsCytron Dual channel 10A Motor Driver UNO Robot Controller
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
-19%
Brushed / Brushless DC motor Driver, MotorsDual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
SmartElex 30D Smart Motor Driver (Powered by Raspberry Pi)
-18%
Brushed / Brushless DC motor Driver, MotorsSmartElex 30D Smart Motor Driver (Powered by Raspberry Pi)
- Supplying 30 amps continuously with peak currents up to 85 amps (2 Sec) per channel.
- Support motor voltage from 7V to 28V.
- Onboard Low Internal resistance MOSFETs are switched at 16KHz frequency.
- Overcurrent protection and indication.
- Thermal protection.
- Type-C USB for SERIAL Mode
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
-
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 12A Motor Driver
- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 25A Motor Driver
- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: n/a - 25A continuous, 50A peak per channel
-
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 32A Motor Driver
- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
SKU: n/a
