Current and Voltage Sensor
Showing all 10 results
-
Current and Voltage Sensor
Voltage Detection Sensor Module 25V
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino
- Voltage input range: DC 0-25 V
- Voltage detection range: DC 0.02445 V to 25 V
- Voltage analog resolution : 0.00489 V
SKU: n/a -
Current and Voltage Sensor
5A range of single-phase AC current sensor module
- Onboard precision microcurrent transformer.
- Onboard sampling resistor.
- The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.
- Rated input current: 5A
- Rated output current: 5mA
- Change: 1000: 1
- The linear range: 0 ~ 10A (100 ohms)
- Linearity: 0.2%
SKU: n/a -
Current and Voltage Sensor
30A range Current Sensor Module ACS712
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 30A
- Sensitivity: 100mV/A
SKU: n/a -
Current and Voltage Sensor
5A range Current Sensor Module ACS712
- Low-noise analog signal path.
- Device bandwidth is set via the new FILTER pin.
- 5 µs output rise time in response to step input current.
- Small footprint, low-profile SOIC8 package.
- 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
SKU: n/a -
Current and Voltage Sensor
CJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
-32%Current and Voltage SensorCJMCU-219 INA219 I2C Interface No Drift Bi-directional Current / Power Supply Monitoring Module
- 0.1 ohm 1% 2W current sense resistor
- Up to +26V target voltage
- Up to ±3.2A current measurement, with ±0.8mA resolution
- Senses Bus Voltages from 0 to 26 V
- 2C- or SMBus-compatible interface. The
- Reports Current, Voltage, and Power.
SKU: n/a -
Current and Voltage Sensor
20A Range Current Sensor Module ACS712
- Low-noise analog signal path
- Device bandwidth is set via the new FILTER pin
- 5 µs output rise time in response to step input current
- Small footprint, low-profile SOIC8 package
- 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: 20A
- Sensitivity: 100mV/A
SKU: n/a -
Current and Voltage Sensor
5A 12V Overcurrent Protection AC Current Detection Sensor Module
LC 5A Over-current protection Sensor module uses a current transformer to collect the AC signal to achieve the relay over-current signal output within 0-5A. Relay pull while over-current, relay released while not over-current
SKU: n/a -
Current and Voltage Sensor
SCT-013-030 Non-invasive AC Current Sensor Clamp Sensor 30A
- Input Current : 0-30A
- Output Mode: 0-1V @ 30mA
- Frequency: 50HZ-150KHZ
- Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W)
- Output Plug 3.5mm
- Dielectric Strength 6000V AC/1min
- Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection
- Meet UL94-V0 flame retardant properties
SKU: n/a -