DC Motor Speed Controller
Showing all 17 results
-
Breakout Board
IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi
- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- Using original IRF520 Power MOS, you can adjust the output PWM
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
-19%
Brushed / Brushless DC motor Driver, Motors20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
-14%
Brushed / Brushless DC motor Driver, MotorsCytron Enhanced 13Amp DC Motor Driver 30A peak (10 seconds) MD10C
- Bi-directional control for 1 brushed DC motor, single channel
- Support motor voltage ranges from 5V to 30V.
- Maximum current up to 13A continuous and 30A peak (10 seconds).
- 3.3V and 5V logic level input.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
MD13S 13Amp DC Motor Driver – GROVE Compatible
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
Cytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
-12%
Brushed / Brushless DC motor Driver, MotorsCytron MDD10A Dual Channel Enhanced 10Amp DC Motor Driver 30A Peak
- Bi-directional control of 2 brushed DC motor.
- Support motor voltage ranges from 5V to 25V.
- Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
- Solid state components provide faster response time and eliminate the wear and tear of the mechanical relay.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Monster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
-17%
Brushed / Brushless DC motor Driver, MotorsMonster Moto Shield VNH2SP30 Motor Driver 14A (Peak 30A)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 34 mΩ
- Maximum PWM frequency: 10 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron 30Amp DC Motor Driver (Peak 80Amp) MD30C R2
- Bi-directional control of 1 brushed DC motor.
- Motor Voltage: 5V – 30V.
- Maximum Current: 80A peak (1 second), 30A continuously.
- Reverse polarity protection.
- 3.3V and 5V logic level input.
- Fully NMOS H-Bridge for better efficiency and no heat sink is required.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Dual channel 10A Motor Driver UNO Robot Controller
-13%
Brushed / Brushless DC motor Driver, MotorsCytron Dual channel 10A Motor Driver UNO Robot Controller
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Dual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
-19%
Brushed / Brushless DC motor Driver, MotorsDual Monster Moto Shield VNH3ASP30 DC Motor Driver 2x14A (Peak 30A)
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 19 mΩ (per leg)
- Maximum PWM frequency: 20 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
-
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 12A Motor Driver
- 12A continuous, 25A peak per channel Up to 24V in
- Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Peak Current (A): 25A
- Continuous Current (A): 12
- Operating Voltage(VDC): 18 to 24V
- No. of Channels: 2
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron Smart Drive Mdds30 Dual 30A (80A Peak)
- Battery low voltage indicator.
- Battery over voltage indicator.
- Thermal protection.
- Current limit protection.
- Bi-directional control for dual brushed DC motor.
- Support motor voltage from 7V to 35VDC.
- Dimension: 103 x 97 x 40 (LxWxH) mm.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 25A Motor Driver
- 25A continuous, 50A peak per channel
6-30V nominal, 33.6V absolute maximum - Synchronous regenerative drive
- Ultra-sonic switching frequency
- Thermal and overcurrent protection
- Lithium protection mode
- Input modes: Analog, R/C, simplified serial, packetized serial
SKU: n/a - 25A continuous, 50A peak per channel
-
Brushed / Brushless DC motor Driver, Motors
Sabertooth Dual 32A Motor Driver
- 32A continuous, 64A peak per channel
- 6-30V nominal, 33.6V absolute maximum
- Synchronous regenerative drive
- Ultrasonic 30 kHz switching frequency
- Thermal and overcurrent protection
- Battery protection mode
- USB control and monitoring
- USB serial converter mode for Kangaroo x2
- Configurable current limiting
- Custom user modes
- 12-bit motor outputs
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: n/a -
