Motor Driver
Showing all 18 results
-
Breakout Board
IRF520 MOSFET Driver Module for Arduino ARM Raspberry pi
- Voltage: 3.3 – 5V.
- Ports: Digital Level.
- Output load voltage: 0-24 V.
- Output load current: <5A (1A above need to add heat sink).
- Platform: Arduino, MCU, ARM, raspberry pi.
- Using original IRF520 Power MOS, you can adjust the output PWM
SKU: n/a -
Development Boards, Shield for Arduino
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
-14%
Development Boards, Shield for ArduinoCNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open-source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Coolant enable.
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- 4-Axis support (X, Y, Z, A-Can duplicate X, Y, Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: n/a -
Development Boards, Shield for Arduino
L293D Motor Driver/Servo Shield for Arduino
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes.
- Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, or interleaved stepping.
SKU: n/a -
Development Boards, Shield for Arduino
Cytron G15 Shield
-
Arduino reset button
-
4 x G15 Cube Servo ports.
-
External power port for a servo with polarity protection
-
Stackable I/O header pin
-
Selectable digital pins for the control pin with mini jumpers
-
TX and RX indicator LEDs to show communication activities, only on Rev2.0.
-
Selectable Serial pins, Either hardware serial or software serial via mini jumpers, only on Rev2.0
SKU: n/a -
-
Motors, Servo Motor Driver
16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
-18%
Motors, Servo Motor Driver16-Channel 12-bit PWM/Servo Driver I2C interface PCA9685 for Arduino Raspberry Pi
- Adjustable frequency PWM up to about 1.6 KHz
- 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
- Configurable push-pull or an open-drain output
- The output enable pin to quickly disable all the outputs
- Terminal block for power input
- Reverse polarity protection on the terminal block input
- Green power-good LED
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
-19%
Brushed / Brushless DC motor Driver, Motors20A PWM DC Motor Speed Regulator Module (9V, 12V, 24V, 36V, 48V, 60V)
- Adjustable speed range: 0%-100%.
- Speed adjustment way: Potentiometer.
- Output voltage: Linear under load.
- Speed control type: Basins.
- Output voltage: Load Linear
- Type: Adjusting flow
- The motor running condition adjustment: Forward / Stop / Reverse
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
MD13S 13Amp DC Motor Driver – GROVE Compatible
-
Support motor voltage ranges from 6V to 30V
-
Maximum current up to 13A continuous and 30A peak (10 seconds).
-
GROVE compatible
-
3.3V and 5V logic level input.
-
SMD compatible
- Peak Current (A): 30 (10 seconds)
- Continuous Current (A): 1
- No. of Channels: 1
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
Cytron Dual channel 10A Motor Driver UNO Robot Controller
-13%
Brushed / Brushless DC motor Driver, MotorsCytron Dual channel 10A Motor Driver UNO Robot Controller
- Onboard 1A (maximum) 5V voltage regulator.
- Onboard 500mA (maximum) 3.3V voltage regulator.
- 0-5V digital outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).(4 pin used for Motor driver)
- 6 Analog Inputs (Can be digital I/O too).
- Maximum current up to 10A continuous and 30A Peak.
- ISP 6-pin Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- R3 Shield Compatible.
SKU: n/a -
Brushed / Brushless DC motor Driver, Motors
Cytron SmartDriveDuo-10 MDDS10 DC MOTOR DRIVER
-
Single power operation
-
Dual Channels means it can drive two brush motor independently, or mixed.
- Support Signed magnitude and Locked Anti-phase in PWM mode.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Power, Error indicator, RUN status (Left and Right) LEDs
-
On board reset button to restart the MCU after changing operation mode.
-
Operating modes: RC (RC servo signal), Analog, PWM, simplified and packetized UART.
SKU: n/a -
-
Brushed / Brushless DC motor Driver, Motors
Cytron SmartDriveDuo-60 MDDS60 60A (100A peak)
-
Input Voltage (Motor): 10 – 45VDC
- Maximum current up to 100A peak (1 second), 60A continuously, each channel.
-
Two manual/test buttons for each channel.
-
Two output indicator LEDs for each channel.
-
Suitable for combat or sumo robot.
- Battery Low Voltage Monitoring Mode
- DC Brush motor Driver, not for brushless motor
- Dual Channels, it can drive two brush motor independently, or mixed.
- Version: Rev 1.10
SKU: n/a -
-
-
Motors, Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
-15%
Motors, Stepper Motor DriversTB6600 Stepper Motor Driver Controller 4A 9~42V TTL 16 Micro-Step CNC 1 Axis
- Input Current: 0~5A
- Output Current: 0.5~4.0A
- Control Signal: 3.3~24V
- Power (MAX): 160W
- Micro Step: 1, 2/A, 2/B, 4, 8, 16, 32
- Temperature: -10～45℃
- H bridge bipolar constant current drive.
SKU: n/a -
Motors, Stepper Motor Drivers
TB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
-14%
Motors, Stepper Motor DriversTB6560 Driver Board 3A CNC Router Single 1 Axis Controller Stepper Motor
- Driver Chip: TB6560AHQ
- Operating Voltage: 10-35V
- Nominal Voltage: 24V
- With the large heat sink to ensure good heat dissipation
- 6N137 high-speed OptoCoupler, to ensure a high speed without step out.
SKU: n/a -
Motors, Stepper Motor Drivers
TB6600 Stepper Motor Driver Controller 8~50V 4.5A
- Supply Voltage: 8V – 50V DC (36V recommended).
- Output current: 0.3A – 4.5A (peak value of 5A).
- Micro Step: 1, 2, 8, 16.
- Maximum PWM frequency: 200kHz.
- Adjustments for the maximum current of the LED: 1A, 2.2A, 3.3A, 4.5A.
- Operating temperature: -10 to + 45 ° С.
SKU: n/a -
Motors, Stepper Motor Drivers
Leadshine DM542 Digital Stepper Motor Driver
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology
SKU: n/a -
Arduino Boards and Accessories, Development Boards
L293D Motor Driver/Servo Shield for Arduino
1. Can drive 4 DC motors or 2 stepper motors or 2 Servos
2. 2 interface for 5V Servo connected to the high-resolution dedicated timer no jitter
2. Up to 4 bi-directional DC motors with individual 8-bit speed selection
4. Up to 2 stepper motors with single coil, double coil or interleaved stepping.
5. 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DCSKU: n/a
