“HSKRC 3 Inch 140mm Carbon Fiber Racing Kit” has been added to your cart. View cart

-8%

Drone, GPS Modules

FPV NEO-M8N GPS amp Compass Support DJI Naza M V1 & V2 Lite Flight Controller

Name: FPV NEO-M8N GPS amp Compass Support DJI Naza M V1 &amp; V2 Lite Flight Controller
SKU: 10274
Availability: BackOrder

Availability:

Available on backorder

Add to wishlist

Receiver type 72-channel M8 engine.
Sensitivity Tracking & Nav: –167 dBm.
Oscillator TCXO (NEO-M8N/Q).
RTC crystal Built-In.
Lowest noise figure (NEO-M8N/Q).
Anti-jamming Active CW detection and removal. Extra.
Onboard SAW bandpass filter (NEO-M8N/Q).
Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
Supported antennas Active and passive.

₹2,219.00 ~~₹2,399.00~~

Available on backorder

Description
Reviews

Supports DJI Naza M V1 & V2 Lite Flight Controllers with FPV NEO-M8N GPS amp Compass. The NEO-M8N is a new generation GPS device that boasts low power consumption and high precision. Its ultimate accuracy is 0.6 meters, or about 0.9 meters, which is greater than the 1.4-1.6 meters accuracy of the NEO-7N, the previous generation device. It also supports more protocols, including GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and mode.

32-bit processing, significantly better than an 8-bit CPU, is compatible with the NAZA M V1 & V2 flight controller. Please pay attention to the GPS’s arrow, which represents a flyer’s head. Comparable GPS calibration and application. includes a 30-cm soft silicone gel cable. A surface was covered with black rubber to make it softer. To lessen signal interference from other electrical devices, a metal foil label has been placed on the bottom of the GPS (Notice: black cable= GND, white cable= TX, yellow cable= RX, red cable= 5V, 3.3-7.5V is OK).

Note: To calibrate the electronic compass is the first important thing when received your GPS.

Specification:

Model	FPV Ublox NEO-M8N
Receiver Type	72-channel Ublox M8 engine.
Main Chip	Ublox NEO-M8N
Sensitivity (dBm)	–148, –156
Position Accuracy (Meter)	2, 2.5
Acceleration (g)	<4
Navigation Update Rate	up to 18 HZ.
Operating Temperature Range (°C):	-24 to 84
Input Interface	36219, 36218, 36216, 36217
Tracking Sensitivity (dBm)	–167 dBm.
Co-Ordinate System	WGS-84
Capture Time	0.1s Average
Boot Time	1S
Dimensions (mm) LxWxH	(dia x width), 54 x 15.2
Weight (gm)	28
Cable Length (cm)	30
Input Supply Voltage (VDC)	1.4 ~ 3.6
Shipping Weight	0.135 kg
Shipping Dimensions	7 × 4 × 1 cm

Feature:

Assistance AssistNow GNSS Online.
AssistNow GNSS Offline (up to 35 days)3.
AssistNow Autonomous (up to 6 days).
OMA SUPL & 3GPP compliant.
Oscillator TCXO (NEO-M8N/Q).
Crystal (NEO-M8M).
RTC crystal Built-In.
Noise figure On-chip LNA (NEO-M8M). Extra LNA for.
Lowest noise figure (NEO-M8N/Q).
Anti-jamming Active CW detection and removal. Extra.
Onboard SAW bandpass filter (NEO-M8N/Q).
Memory ROM (NEO-M8M/Q) or Flash (NEO-M8N).
Supported antennas Active and passive.
Odometer Travelled distance.
Data-logger For position, velocity, and time (NEO-M8N).
RoHS compliant (lead-free).
Manufactured and fully tested in ISO/TS 16949 certified production sites.
Uses M8 chips qualified according to AEC-Q100.
Supply voltage 1.65 V to 3.6 V (NEO-M8M).
Power consumption4 23 mA @ 3.0 V (continuous).
5 mA @ 3.0 V Power Save Mode.
(1 Hz, GPS mode only).
NEO-M8N-0 M8 Concurrent GNSS LCC Module.
TCXO, flash, SAW, LNA.
Time pulse Configurable 0.25 Hz to 10 MHz.
Using 32-bit processor, compatible with DJI NAZA LITE V1 & V2 flight controller, incomparably superior to the 8-bit processor.
Please take notice of the arrow on GPS, which stands for the head of the flyer.
Similar calibration and usage with DJI GPS.
Coming with soft silicone gel cable 30cm.
For softness, black rubber was wrapped on the surface.
(Notice: black cable= GND, white cable=TX, yellow cable=RX, red cable=5V, 3.3-7.5V is ok).
Metal foil label has been mounted on the bottom of GPS to reduce signal interference from other electronic equipment.